Trade In Products

Section	Like New	Very Good	Good	Average
Grip	High quality grip	High quality grip	High quality grip	High quality grip
Shaft	No wear, no bag wear	Slight wear, graphics intact, no bag wear	Graphics fully visible, minimal bag wear	Graphics may be worn, fully functional
Face	Sharp grooves, paint-fill intact	Slight play wear, paint-fill intact	Minor scratches, grooves still sharp	Worn grooves, paint-fill may be missing
Sole	Minor brush marks only	Light wear from grass contact	Scratches from steady use, no structural damage	Heavy-use scratches, paint may be missing
Woods Top/Crown	Barely visible scratch or chip	Barely visible scratch or chip	Small chips/scratches, not visible casually	Visible marks/chips, no performance impact
Irons Topline/Body	Few cosmetic scratches, great condition	Few cosmetic scratches, great condition	Wear consistent with use, no structural damage	Cosmetic scratches/nicks, playability unaffected
Headcover (Woods & Putter)	Matching model-specific headcover guaranteed	Generic Callaway headcover guaranteed	Generic Callaway headcover guaranteed	Generic Callaway headcover guaranteed

Find the right:

Drivers

Find the right Drivers

Head Loft

Choosing the correct loft in your driver is critical in producing a proper launch angle. Golfers with a slower swing speed will benefit from a higher lofted driver (as it helps to get the ball in the air more easily) and the result will be higher trajectory, longer carry, and greater distance. Look at your average swing speed in order to determine the proper loft for your driver. 10.5° is the standard loft for the average men’s driver, 12° is the standard loft for the average women’s driver.

Swing speed	Recommended loft
60 - 70 MPH (<165 YARDS)	12 - 15° OF LOFT
70 - 80 MPH (165 - 200 YARDS)	11 - 13° OF LOFT
80 - 90 MPH (200 - 240 YARDS)	10 - 12° OF LOFT
90 - 100 MPH (240 - 275 YARDS)	9 - 11° OF LOFT
100 MPH+ (>275 YARDS)	8 - 10° OF LOFT

*Most Callaway Golf drivers come with a loft setting of 9, 10.5 or 12 degrees of loft, and can be adjusted to either -1 or +2 degrees of loft.

Shaft Flex

Choosing the right shaft flex for your game is crucial: without the correct flex, golfers will have a harder time making solid contact with the ball on a consistent basis, affecting the direction and distance of their shots. As a general guide, you can determine your shaft flex based on your clubhead speed. "R" is the standard shaft flex for the average men’s driver, "Womens/Ladies" is the standard shaft flex for the average women’s driver.

Clubhead speed	Recommended shaft flex
< 70 MPH (113 KM/H)	WOMEN’S: <55G
70 - 80 MPH (113 - 128 KM/H)	LIGHT: 45 - 60G
80 - 90 MPH (128 - 144 KM/H)	REGULAR: 55 - 70G
90 - 105 MPH (144 - 168 KM/H)	STIFF: 60 - 75G
> 105 MPH (168 KM/H)	X-STIFF: 75 - 90G

*If you’re at the lower end of your clubhead speed category, select a shaft weight at the lower end of the scale, and vice versa.

Shaft Length

Choosing the correct length of shaft will ensure you have the optimum level of control over your driver. The standard length of a driver is 45.75″ for men and 44.75″ for women. Your height and your level of control over the driver will determine the correct shaft length for you. A shorter golfer should go down 0.5″ to 1″. A golfer with less control over their driver might also consider going down by 0.5″ to 1″.

Irons

Find the right Irons

Shaft Flex

Clubhead speed	Recommended shaft flex
< 60 MPH (97 KM/H)	WOMEN’S: <55G
60 - 70 MPH (97 - 113 KM/H)	LIGHT: 55 - 75G
70 - 80 MPH (113 - 129 KM/H)	REGULAR: 55 - 125G
80 - 90 MPH (129 - 145 KM/H)	STIFF: 60 - 75G
> 90 MPH (145 KM/H)	X-STIFF: 85 - 120G

*If you’re at the lower end of your clubhead speed category, select a shaft weight at the lower end of the scale, and vice versa.

Shaft Length

Selecting the correct club length will ensure the golfer is in the address position which can be maintained throughout the golf swing. Too long a club length will cause a shorter player to stand too upright, while too short a club length will cause a taller player to stoop over the club.

Use this guide to determine which club length and lie is right for you, based on your height and wrist-to-floor measurement:

Length + Lie Measurement

(↔ Player Height / ↕ Wrist to Floor)

HEIGHT (inches)	5′0″	5′2″	5′4″	5′6″	5′8″	5′10″	6′0″	6′2″	6′4″	6′6″
30.5″	-2″	-2″	-1.5″	-1.5″	-1″
31″	-2″	-1.5″	-1.5″	-1″	-1″
31.5″	-2″	-1.5″	-1.5″	-1″	-1″	-0.5″
32″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″
32.5″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″	STD
33″		-1″	-1″	-0.5″	-0.5″	STD	STD
33.5″		-1″	-1″	-0.5″	-0.5″	STD	STD	STD
34″			-0.5″	-0.5″	STD	STD	STD	STD
34.5″			-0.5″	-0.5″	STD	STD	STD	STD	STD
35″				STD	STD	STD	STD	STD	+0.5″
35.5″				STD	STD	STD	STD	STD	+0.5″	+1″
36″					STD	STD	STD	STD	+0.5″	+1″
36.5″					STD	STD	STD	+0.5″	+1″	+1.5″
37″						STD	STD	+0.5″	+1″	+1.5″
37.5″						STD	+0.5″	+1″	+1.5″	+2″
38″							+0.5″	+1″	+1.5″	+2″

3 Flat 2 Flat 1 Flat STD 1 Up 2 Up 3 Up

Women’s clubs are traditionally 1″ shorter than men’s. To determine the correct length for a woman, simply add one inch to the length suggested in the chart. For example, if the chart suggests shortening a man’s club by one inch, a woman’s club (already one inch shorter) might not need any length adjustment.

* Measurements should be performed by someone other than yourself.

** Lie angles listed are intended as a reference point. Professional custom fitting is needed to determine correct lie angle.

Shaft Material

Irons come with either graphite or steel shafts. Golfers with a lower swing speed would generally perform better with a graphite shaft, as it can help with getting the ball in the air.

Head Lie Angle

Getting the correct lie angle of your iron will ensure the position of the club head at address and impact will strike the ground, rather than the heel or toe. A club which is too upright for a golfer will cause the clubface to close, resulting in a pull or a hook (for right-handed players), while a club which is too flat will hit the ground with the toe, causing the clubface to open and resulting in a push or a slice (for right-handed players).

Wedges

Find the right Wedges

Head Loft

The degrees of head loft in a wedge determine which type of wedge it is. The higher degree of loft in a wedge, the higher the shot.

Typical degrees of loft	Wedge type
46 - 48 DEGREES	PITCHING WEDGE
48 - 52 DEGREES	GAP WEDGE
54 - 56 DEGREES	SAND WEDGE
58 - 64 DEGREES	LOB WEDGE

Shaft Length

Getting the correct lie angle of your wedge will ensure the position of the club head at address and impact will strike the ground, rather than the heel or toe. A club which is too upright for a golfer will cause the clubface to close, resulting in a pull or a hook (for right-handed players), while a club which is too flat will hit the ground with the toe, causing the clubface to open and resulting in a push or a slice (for right-handed players).

Use this guide to determine which club length and lie is right for you, based on your height and wrist-to-floor measurement:

Length + Lie Measurement

(↔ Player Height / ↕ Wrist to Floor)

HEIGHT (inches)	5′0″	5′2″	5′4″	5′6″	5′8″	5′10″	6′0″	6′2″	6′4″	6′6″
30.5″	-2″	-2″	-1.5″	-1.5″	-1″
31″	-2″	-1.5″	-1.5″	-1″	-1″
31.5″	-2″	-1.5″	-1.5″	-1″	-1″	-0.5″
32″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″
32.5″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″	STD
33″		-1″	-1″	-0.5″	-0.5″	STD	STD
33.5″		-1″	-1″	-0.5″	-0.5″	STD	STD	STD
34″			-0.5″	-0.5″	STD	STD	STD	STD
34.5″			-0.5″	-0.5″	STD	STD	STD	STD	STD
35″				STD	STD	STD	STD	STD	+0.5″
35.5″				STD	STD	STD	STD	STD	+0.5″	+1″
36″					STD	STD	STD	STD	+0.5″	+1″
36.5″					STD	STD	STD	+0.5″	+1″	+1.5″
37″						STD	STD	+0.5″	+1″	+1.5″
37.5″						STD	+0.5″	+1″	+1.5″	+2″
38″							+0.5″	+1″	+1.5″	+2″

3 Flat 2 Flat 1 Flat STD 1 Up 2 Up 3 Up

NOTE: Selecting the correct club length will ensure the golfer is in the address position which can be maintained throughout the golf swing. Too long a club length will cause a shorter player to stand too upright, while too short a club length will cause a taller player to stoop over the club.

* Measurements should be performed by someone other than yourself.

** Lie angles listed are intended as a reference point. Professional custom fitting is needed to determine correct lie angle.

Shaft Material

Wedges come with either graphite or steel shafts, although steel shafts are more common. Golfers with a lower swing speed would generally perform better with a graphite shaft, as it can help with getting the ball in the air.

Head Lie Angle

Use this guide to determine which club length and lie is right for you, based on your height and wrist-to-floor measurement:

Length + Lie Measurement

(↔ Player Height / ↕ Wrist to Floor)

HEIGHT (inches)	5′0″	5′2″	5′4″	5′6″	5′8″	5′10″	6′0″	6′2″	6′4″	6′6″
30.5″	-2″	-2″	-1.5″	-1.5″	-1″
31″	-2″	-1.5″	-1.5″	-1″	-1″
31.5″	-2″	-1.5″	-1.5″	-1″	-1″	-0.5″
32″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″
32.5″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″	STD
33″		-1″	-1″	-0.5″	-0.5″	STD	STD
33.5″		-1″	-1″	-0.5″	-0.5″	STD	STD	STD
34″			-0.5″	-0.5″	STD	STD	STD	STD
34.5″			-0.5″	-0.5″	STD	STD	STD	STD	STD
35″				STD	STD	STD	STD	STD	+0.5″
35.5″				STD	STD	STD	STD	STD	+0.5″	+1″
36″					STD	STD	STD	STD	+0.5″	+1″
36.5″					STD	STD	STD	+0.5″	+1″	+1.5″
37″						STD	STD	+0.5″	+1″	+1.5″
37.5″						STD	+0.5″	+1″	+1.5″	+2″
38″							+0.5″	+1″	+1.5″	+2″

3 Flat 2 Flat 1 Flat STD 1 Up 2 Up 3 Up

* Measurements should be performed by someone other than yourself.

** Lie angles listed are intended as a reference point. Professional custom fitting is needed to determine correct lie angle.

Head Grind

Grind	Features
C-GRIND	Increased relief on the heel and toe area, making it easier to play from a wider variety of shots with an open face.
S-GRIND	Medium-width sole with slight ribbon at the back and moderate relief to keep the leading edge low through impact. The most popular grind option for a wide variety of conditions and swing types.
X-GRIND	Features a narrow, high-bounce crescent sole, with the low point near the front.
W-GRIND	Wider centre and toe area of the sole with moderate heel relief and generous front-to-back camber prevents digging without increasing bounce.

Head Bounce

Head Loft

Find the right Head Loft

Drivers

Swing speed	Recommended loft
60 - 70 MPH (<165 YARDS)	12 - 15° OF LOFT
70 - 80 MPH (165 - 200 YARDS)	11 - 13° OF LOFT
80 - 90 MPH (200 - 240 YARDS)	10 - 12° OF LOFT
90 - 100 MPH (240 - 275 YARDS)	9 - 11° OF LOFT
100 MPH+ (>275 YARDS)	8 - 10° OF LOFT

*Most Callaway Golf drivers come with a loft setting of 9, 10.5 or 12 degrees of loft, and can be adjusted to either -1 or +2 degrees of loft.

Wedges

The degrees of head loft in a wedge determine which type of wedge it is. The higher degree of loft in a wedge, the higher the shot.

Typical degrees of loft	Wedge type
46 - 48 DEGREES	PITCHING WEDGE
48 - 52 DEGREES	GAP WEDGE
54 - 56 DEGREES	SAND WEDGE
58 - 64 DEGREES	LOB WEDGE

Shaft Flex

Find the right Shaft Flex

Drivers

Clubhead speed	Recommended shaft flex
< 70 MPH (113 KM/H)	WOMEN’S: <55G
70 - 80 MPH (113 - 128 KM/H)	LIGHT: 45 - 60G
80 - 90 MPH (128 - 144 KM/H)	REGULAR: 55 - 70G
90 - 105 MPH (144 - 168 KM/H)	STIFF: 60 - 75G
> 105 MPH (168 KM/H)	X-STIFF: 75 - 90G

*If you’re at the lower end of your clubhead speed category, select a shaft weight at the lower end of the scale, and vice versa.

Irons

Clubhead speed	Recommended shaft flex
< 60 MPH (97 KM/H)	WOMEN’S: <55G
60 - 70 MPH (97 - 113 KM/H)	LIGHT: 55 - 75G
70 - 80 MPH (113 - 129 KM/H)	REGULAR: 55 - 125G
80 - 90 MPH (129 - 145 KM/H)	STIFF: 60 - 75G
> 90 MPH (145 KM/H)	X-STIFF: 85 - 120G

*If you’re at the lower end of your clubhead speed category, select a shaft weight at the lower end of the scale, and vice versa.

Shaft Length

Find the right Shaft Length

Drivers

Irons

Use this guide to determine which club length and lie is right for you, based on your height and wrist-to-floor measurement:

Length + Lie Measurement

(↔ Player Height / ↕ Wrist to Floor)

HEIGHT (inches)	5′0″	5′2″	5′4″	5′6″	5′8″	5′10″	6′0″	6′2″	6′4″	6′6″
30.5″	-2″	-2″	-1.5″	-1.5″	-1″
31″	-2″	-1.5″	-1.5″	-1″	-1″
31.5″	-2″	-1.5″	-1.5″	-1″	-1″	-0.5″
32″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″
32.5″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″	STD
33″		-1″	-1″	-0.5″	-0.5″	STD	STD
33.5″		-1″	-1″	-0.5″	-0.5″	STD	STD	STD
34″			-0.5″	-0.5″	STD	STD	STD	STD
34.5″			-0.5″	-0.5″	STD	STD	STD	STD	STD
35″				STD	STD	STD	STD	STD	+0.5″
35.5″				STD	STD	STD	STD	STD	+0.5″	+1″
36″					STD	STD	STD	STD	+0.5″	+1″
36.5″					STD	STD	STD	+0.5″	+1″	+1.5″
37″						STD	STD	+0.5″	+1″	+1.5″
37.5″						STD	+0.5″	+1″	+1.5″	+2″
38″							+0.5″	+1″	+1.5″	+2″

3 Flat 2 Flat 1 Flat STD 1 Up 2 Up 3 Up

* Measurements should be performed by someone other than yourself.

** Lie angles listed are intended as a reference point. Professional custom fitting is needed to determine correct lie angle.

Wedges

Use this guide to determine which club length and lie is right for you, based on your height and wrist-to-floor measurement:

Length + Lie Measurement

(↔ Player Height / ↕ Wrist to Floor)

HEIGHT (inches)	5′0″	5′2″	5′4″	5′6″	5′8″	5′10″	6′0″	6′2″	6′4″	6′6″
30.5″	-2″	-2″	-1.5″	-1.5″	-1″
31″	-2″	-1.5″	-1.5″	-1″	-1″
31.5″	-2″	-1.5″	-1.5″	-1″	-1″	-0.5″
32″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″
32.5″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″	STD
33″		-1″	-1″	-0.5″	-0.5″	STD	STD
33.5″		-1″	-1″	-0.5″	-0.5″	STD	STD	STD
34″			-0.5″	-0.5″	STD	STD	STD	STD
34.5″			-0.5″	-0.5″	STD	STD	STD	STD	STD
35″				STD	STD	STD	STD	STD	+0.5″
35.5″				STD	STD	STD	STD	STD	+0.5″	+1″
36″					STD	STD	STD	STD	+0.5″	+1″
36.5″					STD	STD	STD	+0.5″	+1″	+1.5″
37″						STD	STD	+0.5″	+1″	+1.5″
37.5″						STD	+0.5″	+1″	+1.5″	+2″
38″							+0.5″	+1″	+1.5″	+2″

3 Flat 2 Flat 1 Flat STD 1 Up 2 Up 3 Up

* Measurements should be performed by someone other than yourself.

** Lie angles listed are intended as a reference point. Professional custom fitting is needed to determine correct lie angle.

Shaft Material

Find the right Shaft Material

Irons

Irons come with either graphite or steel shafts. Golfers with a lower swing speed would generally perform better with a graphite shaft, as it can help with getting the ball in the air.

Wedges

Head Lie Angle

Find the right Head Lie Angle

Irons

Wedges

Use this guide to determine which club length and lie is right for you, based on your height and wrist-to-floor measurement:

Length + Lie Measurement

(↔ Player Height / ↕ Wrist to Floor)

HEIGHT (inches)	5′0″	5′2″	5′4″	5′6″	5′8″	5′10″	6′0″	6′2″	6′4″	6′6″
30.5″	-2″	-2″	-1.5″	-1.5″	-1″
31″	-2″	-1.5″	-1.5″	-1″	-1″
31.5″	-2″	-1.5″	-1.5″	-1″	-1″	-0.5″
32″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″
32.5″	-1.5″	-1.5″	-1″	-1″	-0.5″	-0.5″	STD
33″		-1″	-1″	-0.5″	-0.5″	STD	STD
33.5″		-1″	-1″	-0.5″	-0.5″	STD	STD	STD
34″			-0.5″	-0.5″	STD	STD	STD	STD
34.5″			-0.5″	-0.5″	STD	STD	STD	STD	STD
35″				STD	STD	STD	STD	STD	+0.5″
35.5″				STD	STD	STD	STD	STD	+0.5″	+1″
36″					STD	STD	STD	STD	+0.5″	+1″
36.5″					STD	STD	STD	+0.5″	+1″	+1.5″
37″						STD	STD	+0.5″	+1″	+1.5″
37.5″						STD	+0.5″	+1″	+1.5″	+2″
38″							+0.5″	+1″	+1.5″	+2″

3 Flat 2 Flat 1 Flat STD 1 Up 2 Up 3 Up

* Measurements should be performed by someone other than yourself.

** Lie angles listed are intended as a reference point. Professional custom fitting is needed to determine correct lie angle.

Head Grind

Find the right Head Grind

Wedges

Grind	Features
C-GRIND	Increased relief on the heel and toe area, making it easier to play from a wider variety of shots with an open face.
S-GRIND	Medium-width sole with slight ribbon at the back and moderate relief to keep the leading edge low through impact. The most popular grind option for a wide variety of conditions and swing types.
X-GRIND	Features a narrow, high-bounce crescent sole, with the low point near the front.
W-GRIND	Wider centre and toe area of the sole with moderate heel relief and generous front-to-back camber prevents digging without increasing bounce.

Head Bounce

Find the right Head Bounce

Wedges

Your cart is empty

Filters

Length + Lie Measurement

Length + Lie Measurement

Length + Lie Measurement

Length + Lie Measurement

Length + Lie Measurement

Length + Lie Measurement

Country/Region

Your cart is empty

Filters